KELLY-MOORE PAINT CO INC -- 1685-SERIES DURA-POXY SEMI-GLOSS ACRYLIC ENAMEL ALL COLORS  -- 8010-00F026084
<pre>=====================  Product Identification  =====================

Product ID:1685-SERIES DURA-POXY SEMI-GLOSS ACRYLIC ENAMEL ALL COLORS
MSDS Date:03/05/1990
FSC:8010
NIIN:00F026084
MSDS Number: BQHKZ
=== Responsible Party ===
Company Name:KELLY-MOORE PAINT CO INC
Address:1015 COMMERCIAL ST
City:SAN CARLOS
State:CA
ZIP:94070
Country:US
Info Phone Num:415-592-8337
Preparer's Name:M SCHEFER
CAGE:0Y837
=== Contractor Identification ===
Company Name:KELLY-MOORE PAINT CO INC
Address:987 COMMERCIAL ST
Box:City:SAN CARLOS
State:CA
ZIP:94070
Country:US
Phone:650-592-8337
CAGE:0Y837

=============  Composition/Information on Ingredients  =============

Ingred Name:2-(2-BUTOXYETHYOXY)-ETHANOL, DIETHYLENE GLYCOL MONOBUTYL
    ETHER (BUTYL CARBITOL)
CAS:112-34-5
RTECS #:KJ9100000
Fraction by Wt: <5%

Ingred Name:PROPANOIC ACID, 2-METHYL, MONOESTER
    W/2,2,4-TRIMETHYL-1,3-PENTANEDIOL, TEXANOL	(ESTER ALCOHOL)
CAS:25265-77-4
RTECS #:UF6000000
Fraction by Wt: <5%

Ingred Name:HEXYLENE GLYCOL, 2-METHYL-2,4-PENTANEDIOL
CAS:107-41-5
RTECS #:SA0810000
Fraction by Wt: <5%
Other REC Limits:25 PPM
OSHA PEL:25 PPM
ACGIH TLV:C 21 MG/CUM

Ingred Name:1-(3-CHLOROALLYL)-3,5,7-TRIAZA-1-AZONIAADAMANTANE CHLORIDE,
    DOWICIL 100, DOWCO 184
CAS:4080-31-3
RTECS #:XX8450000

Ingred Name:WEIGHT PER GALLON IN POUNDS: 8-11 LBS
RTECS #:9999999WG

Ingred Name:TITANIUM DIOXIDE, TIO2
CAS:13463-67-7
RTECS #:XR2275000
OSHA PEL:15 MG/M3 TDUST
ACGIH TLV:10 MG/M3 TDUST; 9293

Ingred Name:SILICATES

=====================  Hazards Identification  =====================

Routes of Entry: Inhalation:YES  Skin:NO  Ingestion:NO
Reports of Carcinogenicity:NTP:NO    IARC:NO	OSHA:NO
Health Hazards Acute and Chronic:INHALATION: DIZZINESS, HEADACHE,
    NAUSEA, CONFUSION, UPPER RESPIRATORY TRACT IRRITATION,
    UNCONSCIOUSNESS. SKIN/EYES: IRRITATION.
Explanation of Carcinogenicity:NONE
Medical Cond Aggravated by Exposure:SEE YOUR PHYSICIAN FOR SPECIFIC
    MEDICAL OPINION REGARDING YOUR CONDITION.

=======================  First Aid Measures  =======================

First Aid:INHALATION: REMOVE TO FRESH AIR. RESTORE BREATHING. EYES:
    WASH W/PLENTY OF WATER FOR AT LEAST 15 MINS. SKIN: WIPE OFF W/RAG.
    WASH THOROUGHLY W/SOAP & WATER. INGESTION: OBTAIN MEDICAL ATTENTION
    IN ALL   CASES.

=====================  Fire Fighting Measures  =====================

Flash Point:>200F
Unusual Fire/Explosion Hazard:CLOSED CONTAINERS MAY EXPLODE (DUE TO
    BUILD UP OF STEAM PRESSURE) WHEN EXPOSED TO EXTREME HEAT.

==================  Accidental Release Measures  ==================

Spill Release Procedures:VENTILATE AREA TO PREVENT BUILD-UP OF VAPORS.
    FOR SMALL SPILLS: SOAK UP W/ABSORBENT. FOR LARGER SPILLS: DIKE AREA
    W/ABSORBENT MATERIAL  & SCOOP UP LIQUIDS.

======================	Handling and Storage  ======================

Handling and Storage Precautions:STORE UPRIGHT IN SEALED CONTAINERS
    AWAY FROM HEAT & FLAME.
Other Precautions:AVOID CONTACT W/SKIN/EYES & CLOTHES. AVOID BREATHING
    SPRAY MIST OR DUST.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:USE PARTICLE MASK TO AVOID BREATHING SPRAY MIST
    OR DUST. USE APPROVED RESPIRATOR FOR ORGANIC VAPOR, SUPPLIED AIR OR
    SELF-CONTAINED BREATHING EQUIPMENT.
Ventilation:LOCAL EXHAUST TO KEEP BELOW TLV.
Protective Gloves:RECOMMENDED
Eye Protection:GOGGLES OR GLASSES W/SHIELDS
Work Hygienic Practices:REMOVE & WASH CONTAMINATED CLOTHES BEFORE
    REUSE. WASH HANDS THOROUGHLY AFTER HANDLING.
Supplemental Safety and Health
PRODUCT MAY CONTAIN TITANIUM DIOXIDE OR SILICATES THAT MAY BE NUISANCE
    DUST HAZARDS IN THEIR ORIGINAL DRY POWDER FORM BUT ARE NOT
    HAZARDOUS IN WET PAINT.

==================  Physical/Chemical Properties  ==================

Boiling Pt:B.P. Text:212F
Vapor Density:<1
Evaporation Rate &amp; Reference:SLOWER THAN ETHER
Percent Volatiles by Volume:62-72%

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS
Stability Condition to Avoid:HEAT
Hazardous Decomposition Products:MAY PRODUCE HAZARDOUS FUMES WHEN
    HEATED TO DECOMPOSITION AS IN WELDING.

====================  Disposal Considerations  ====================

Waste Disposal Methods:DISCARD IN LAND FILL IN SEALED METAL CONTAINERS
    AWAY FROM HEAT & FLAME & IN ACCORDANCE W/LOCAL REGULATIONS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.